Today my inverter is showing an error code btp in display. It's not working with battery backup. I am now using the bypass mode at the back of the inverter. My UPS inverter model is Luminous Zelio 1700 with two 12 tubular batteries.
person
brightness_auto
8 Answers
The btp error code in inverters describes that the mains input MCB on the inverter is tripped so as to protect the device from a short circuit or lightening. During this error the inverter will be in OFF position.
Remove any newly connected device or any existing electrical device that may have shorting and try to ON the MCB as well as the inverter.
In some cases btp error may even lead to a board complaint if the MCB couldn't protect the inverter.
Remove any newly connected device or any existing electrical device that may have shorting and try to ON the MCB as well as the inverter.
In some cases btp error may even lead to a board complaint if the MCB couldn't protect the inverter.
BTP error code in Luminous Zelio inverter usually indicates a battery temperature sensing issue. The inverter is designed to shut down when the battery temperature is too high to protect the battery from damage. You can try to reset the inverter by disconnecting the battery and then reconnecting it after a few minutes. If that does not work, then you may need to contact an authorized service center to get the issue resolved.
The BTP error code in the Luminous Zelio inverter indicates a Battery Type Mismatch, signaling that the connected battery does not match the selected battery type setting on the inverter. To resolve this error, ensure that the correct battery type is selected in the inverter settings to match the connected battery.
The "btp" error code appearing on your Luminous Zelio inverter signifies a battery reverse polarity fault. To address this issue, start by carefully inspecting the battery connections. Ensure that the positive (+) and negative (-) terminals are correctly aligned with the corresponding polarities on both the battery and the inverter.
If the connections are correct and the error persists, consult the user manual provided with your inverter for detailed troubleshooting steps. Additionally, reaching out to Luminous customer support can provide specific guidance tailored to your inverter model and help resolve the reverse polarity fault.
If the connections are correct and the error persists, consult the user manual provided with your inverter for detailed troubleshooting steps. Additionally, reaching out to Luminous customer support can provide specific guidance tailored to your inverter model and help resolve the reverse polarity fault.
The "BTP" error code in a Luminous Zelio inverter typically indicates a low battery voltage condition. This error occurs when the inverter detects that the battery voltage has dropped below the acceptable level.To address this issue, you may want to check and take the following steps:Battery Voltage: Verify the voltage of your inverter battery. If it's too low, you may need to recharge or replace the battery.Battery Connections: Ensure that the battery connections are secure and free from corrosion.Charging System: Check if the inverter is receiving a proper charging supply. Ensure that the charging source (grid power or solar) is functioning correctly.Load Conditions: Reduce the connected load on the inverter. Excessive load can lead to a drop in battery voltage.If the issue persists, it's recommended to consult the user manual for your specific model or contact Luminous customer support for further assistance.
Assuming your Glowing Zelio 1700 inverter is showing a mistake code "BTP" and not working with battery reinforcement, attempt these moves toward investigate the issue:
1. take a look at the client manual for investigating steps intended for your model.
2. Guarantee that the battery associations are secure and appropriately associated.
3. Measure the voltage of your batteries utilizing a multimeter.
4. Check the water levels assuming you are utilizing lead-corrosive batteries.
5. Detach gadgets on the off chance that the mistake continues because of over-burden.
6. Take a stab at resetting the inverter by switching it off, detaching it from the power source, and sitting tight for a couple of moments.
7. Check for firmware refreshes for your inverter model.
8. Contact client care or administration focus of Brilliant for help assuming the issue continues.
9. Focus on well-being while working with electrical gear. Look for proficient help from the producer or a certified specialist if uncertain or unfit to investigate the issue yourself.